f35be51c27
cleans up drawing layers
Stephen Hawes
2023-03-06 11:18:57 -05:00
37316d0ea9
fixes deformed outline
Stephen Hawes
2023-03-06 11:01:15 -05:00
f18097ea1e
adds kikit annotations for panelization
Stephen Hawes
2023-03-06 10:50:58 -05:00
92a9864aa0
buttons are really nice here. just a bit of interface with the surface beneath so a great breakaway with support-free printing. buttons cover part of the pcb and feel nice
Stephen Hawes
2023-03-06 09:13:00 -05:00
ec2326c46a
opens up the interface for the slot pcb even more, makes sure the print isnt deformed when the board is mounted
Stephen Hawes
2023-03-06 09:11:31 -05:00
b53c20fc17
fixes spool holder not fitting in frame, uses good geometry for holding spool on
Stephen Hawes
2023-03-06 09:11:01 -05:00
d2b99377e5
adds a bit more clearance for slot pcb tos lide in
Stephen Hawes
2023-03-03 16:44:44 -05:00
2f660ccc30
makes the post in the spool holder a bit longer to prevent spools from rotating about the y axis
Stephen Hawes
2023-03-03 16:19:37 -05:00
90df5c2771
updates assembly to include frame updates
Stephen Hawes
2023-03-03 16:16:46 -05:00
cd63a65ecf
adds indexing wheel mechanical model
Stephen Hawes
2023-03-03 16:16:10 -05:00
9ed5414136
updates controller pcb to have copper keepouts around the countersinks, shifts the buttons to a more centered position
Stephen Hawes
2023-03-03 16:15:41 -05:00
8bfcd81394
updates feeder floor to have tht connectors for strength
Stephen Hawes
2023-03-03 16:14:38 -05:00
c8d1f2c605
adjusts feeder floor to cover THT pins on IDC connector
Stephen Hawes
2023-03-03 16:09:51 -05:00
375bd762d1
greatly improves button feature in frame, removes material to make peel motor cable easier to insert
Stephen Hawes
2023-03-03 16:09:30 -05:00
1fada01f27
adds dogbone cutouts to indexing wheel for better positioning, more alignment features, holes for potential screw-mounted shaft collars
Stephen Hawes
2023-03-03 16:08:50 -05:00
1e7c0c7c42
adds diffusion pcb logo mask footprint
Stephen Hawes
2023-03-03 16:08:05 -05:00
a7ed4264b1
adds light diffusion pcb
Stephen Hawes
2023-03-03 16:07:36 -05:00
a66ba957ed
adds footprint for locking header for UART, adds it to pcb
Stephen Hawes
2023-02-09 11:57:16 -05:00
3ea01fbc81
starting on controller rev10, fixes motor spinning while in bootloader mode by pulling motor enable low with a pulldown resistor, and enabling with PA2 in firmware
Stephen Hawes
2023-02-09 10:45:54 -05:00
a3851a2112
adds passthrough and alignment holes to indexing-wheel cad
Stephen Hawes
2023-02-08 19:09:24 -05:00
bc8e081b1b
removing out folders, ds-store files, and fcstd1 files
Stephen Hawes
2023-02-08 13:51:58 -05:00
cd2e794715
adds bom csv and cleans up cha image files
Stephen Hawes
2023-02-08 13:50:29 -05:00
c6b6a7c4b7
adds fcstd1 files and out folders to gitignore
Stephen Hawes
2023-02-08 13:49:46 -05:00
7ff9705461
loosens up fit of peel gears for shaft mounting and fit in the frame
Stephen Hawes
2023-02-08 13:47:41 -05:00
17dad6b5e6
updates frame to have ledge for fid pcb
Stephen Hawes
2023-02-08 13:46:51 -05:00
e9bcf7fc20
updates pad library file to make pads a bit smaller
Stephen Hawes
2023-02-08 13:46:24 -05:00
aca9c35f2c
updates asm with bolts and fid pcb
Stephen Hawes
2023-02-08 13:45:53 -05:00
0a9bc577c1
adds photon 8mm fid
Stephen Hawes
2023-02-08 13:45:39 -05:00
f6550eb418
updating fill zone outline of feeder floor to work with kikit
Stephen Hawes
2023-02-07 16:56:01 -05:00
ab57eac8c1
uprevs feederfloor to rev06, through hole IDC connector, adds silk for address, makes pads .1mm thinner, vdc has traces both sides
Stephen Hawes
2023-02-07 14:22:39 -05:00
985822d0b3
adds some LCSC part numbers to the schematic
Stephen Hawes
2023-02-07 14:05:11 -05:00
a32820a702
cad tweaks for better fit, worm gear larger id, spool holder smaller post, smaller peel gears for less friction, shorter drive-motor-bracket for an easier time mounting
Stephen Hawes
2023-02-01 09:53:25 -05:00
8bde418bc8
adds wireviz yaml files for feeder floor harness
Stephen Hawes
2023-01-17 18:50:44 -05:00
268e266d86
makes film have a better clearance path for peeling, makes cutout for buttons
Stephen Hawes
2023-01-12 12:12:30 -05:00
3de54c689d
added datasheet for main rgb led
Stephen Hawes
2022-12-09 10:57:28 -05:00
b823c7bddf
cleaned up feeder floor schematic
Stephen Hawes
2022-12-09 10:56:02 -05:00
998eb5b7cb
added drive motor bracket mounting screws
Stephen Hawes
2022-12-09 10:49:53 -05:00
9486f7e7be
schematic cleanup
Stephen Hawes
2022-12-09 10:49:38 -05:00
a07f55b2cc
cad tweaks for rev09 feeder, including first pass at printed buttons, properly recessed nuts in peel gear frame, tweaked feeder floor for new feeder floor pcb
Stephen Hawes
2022-12-09 09:50:03 -05:00
93cd9801c6
adding multi-part footprint for ds28e07
Stephen Hawes
2022-12-09 09:49:01 -05:00
23a94d06bd
this commit represents rev09 of the controller, rev04 of the indexing wheel, and rev05 of the feeder floor
Stephen Hawes
2022-12-09 09:48:28 -05:00
63ebb10ad8
adds 10k pullup to reset
Stephen Hawes
2022-12-08 10:14:23 -05:00
ab78e1af2d
adds second footprint for rgbled, adds testpoints
Stephen Hawes
2022-12-06 10:46:47 -05:00
72d4928337
removes all the indicator leds in exchange for a single rgb. adds diffusion and printed buttons in cad
Stephen Hawes
2022-12-02 14:37:14 -05:00
d02d3a95e4
makes drive motor plug easier to plug into pcb, gives drive motor cable more space to exist in the frame
Stephen Hawes
2022-10-28 13:16:24 -04:00
f4b7170097
tweaks to film gear frame to make the gears easier to pop in
Stephen Hawes
2022-10-27 18:26:18 -04:00
585bdb8637
adds accurate model of worm gear n20, redid cable routing for drive motor, opened up recess for drive motor to fit new type, shifted drive motor bracket closer to the gearbox, guides tape so it doesnt collide with buttons, feeder floor chamfered correctly for easy insertion, guides film so it stays centered in gears
Stephen Hawes
2022-10-26 16:32:18 -04:00
7641f90c9a
working cad setup, requires mods to fit worm gear n20 with flush pcb
Stephen Hawes
2022-10-26 09:30:18 -04:00
3258dbd22f
represents rev08 of feeder controller, rev04 of feeder floor. cad still needs some tweaks.
Stephen Hawes
2022-10-06 16:03:50 -04:00
c89d551814
got feeder floor print updated to match new angles
Stephen Hawes
2022-10-04 16:57:27 -04:00
4583e2b04f
moved feeder motherboard geometry so spring fingers come straight down onto pads
Stephen Hawes
2022-10-04 15:05:47 -04:00
5b0719495a
cleaned up the repo! moved firmware out, cleaned up cad, deleted extra crap
Stephen Hawes
2022-09-20 14:20:18 -04:00
6050d0581f
removes ds store
Stephen Hawes
2022-09-20 13:56:01 -04:00
0573945dd5
switches pin for switch 1 because of arduino support
Stephen Hawes
2022-09-20 13:50:31 -04:00
44f5f5adc8
updates define.h to have pins correct for rev07
Stephen Hawes
2022-09-19 12:53:46 -04:00
25f055d769
adds dsstore to gitignore
Stephen Hawes
2022-08-29 16:00:14 -04:00
ed79c04cdd
represents rev07 feeder controller, rev03 indexing wheel, rev03 feeder floor. also checks in lots of cad work for feeder design and feeder floor design
Stephen Hawes
2022-08-23 12:11:06 -04:00
32e2dc15f8
rev06 pcb
Stephen Hawes
2022-07-28 14:40:46 -04:00
e51ccdd232
firmware updated with encoder support, and support for the f031.
Stephen Hawes
2022-07-28 14:40:30 -04:00
51b8ca6efb
adds in rough beginning of rev06 cad
Stephen Hawes
2022-07-28 14:40:00 -04:00
3c3720078e
Initial commit
Stephen Hawes
2022-07-08 13:05:03 -04:00
Stephen Hawes